LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.
|Published (Last):||9 August 2006|
|PDF File Size:||5.98 Mb|
|ePub File Size:||13.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
The init function can be modified to utilize other special features of the chip not used here.
The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover. The LS is a 24 bit quadrature counter.
Using the LS Quadrature Counter – Northwestern Mechatronics Wiki
The value of the PR register is loaded whenever the counter borrows downticks from daatasheet. This number should be changed based on dagasheet full rotation count of the encoder in use.
Alternatively, at each read the PIC could send back the actual count value. As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for each chip.
The following is a list of registers and the general use of each, even though they are already handled by the code written in a later section. The LS communicates with datashet microcontroller via a bi-directional 8-bit data bus and several control bits.
There are also two pins which output flags when programmed events occur, such as an overflow.
(PDF) LS7166 Datasheet download
This c file simply loops continuously and reads values from the LS This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, the exact position of the motor can be known no matter the amount of time that has passed since the last read.
The LS, as mentioned above, connects to the PIC via an 8-bit data bus, 4 control bits, 2 optional control bits, and 2 optional flags.
This c file contains various functions used to interface with the LS Note that at the end of the init function, the counter limit value is loaded into the PR register.
Note that most pins are active low, and thus must be kept at high at all times unless in use. Views Page Discussion View source History.
Using the LS7166 Quadrature Counter
For more info on these features, see the datasheet. Personal tools Log in. For instance, if the maximum count isand CNTR isthen the actual position is datashet of A motor’s encoder can be connected directly to the LS, datahseet will decode and count pulses as the encoder channels change.
The code in this document only covers divide-by-n binary quadrature mode, and for more advanced features the support code will need to be modified. Because of this, the pic software must be written so that the read value of CNTR is modded by the maximum count number to find the position.
The chip has several other features that can be read about in the datasheet. Because of this, if running the motor backwards continuously counting downthe value of CNTR dataseet always be between 0 and PR at the current position.
In any motor-related application, binary counting is necessary. Using a parallel data bus, a microcontroller can simply read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers.
LS Datasheet(PDF) – LSI Computer Systems
Eventually the CNTR will overflow if not reduced. Retrieved from ” http: The A and B inputs normally serve as quadrature inputs, like those which come from a quadrature encoder like those on most motors. All three can be download from this zip file. A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page.
These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes. Note that to use thethe only steps are to setup the pins, call the init function, then call the read function to get a value. In the code below and example schematic, pins B0-B7 are used for the data bus.