ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.
|Genre:||Health and Food|
|Published (Last):||12 June 2008|
|PDF File Size:||16.51 Mb|
|ePub File Size:||15.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
The bend shall be made on a radius equal to that shown in Table 1 for the applicable grade. Surface Requirement Bend Aztm S1. Thickness is measured along the longitudinal edges of the plate at least 38 in.
For sheet and strip, the bend test specimen shall stand being bent cold through without fracture in the outside of the bent portion. B — 10 Standard Specication for Titanium and Titanium Alloy Strip, Sheet, and Plate1 This standard is issued under the xed designation B; the number immediately following the designation indicates the year of original adoption satm, in the case of revision, the year of last revision.
Ingot hydrogen need not be reported. Current edition approved May 1, MPa Marking and Packaging Each pair of these bends will place opposite surfaces of the sheet or plate material in tension. This standard has been approved for use by agencies of the Department of Defense.
Mechanical properties for conditions other than annealed or plate thickness over 1 in. The bend specimen may be of less than full material thickness; however, the outer surface of the specimen must include the original material surface with no material removal or surface conditioning other than adtm the rounded corners, and must otherwise be representative of the product as supplied.
Permission rights to photocopy adtm standard may also be secured from the ASTM website www. Tensile sstm shall be determined using a strain rate of 0. The report shall b65 results of all chemical analysis, tensile tests, and all other tests required by the specication.
Last previous edition approved in as B — 09a1.
A superscript epsilon indicates an editorial change since the last revision or reapproval. The manufacturer shall not ship material that is outside the limits specied in Table 2 for the applicable grade. For plates up to 10 in. Two bends shall be made in the L direction and two in the T direction. This is in accordance with the round-off method of Practice E Specied thickness was corrected from 0.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown. NOTE 4—The maximum deviation from a at surface does not customarily exceed the tabular tolerance for the longer dimension specied.
Only original conforming test results or the conforming retest results shall be reported to the purchaser. Alternate techniques are discussed in Guide E The characters ashm be not less than 38 in.
ASTM B – 15 Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Approved May zstm, ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Therefore, properties for aged material shall be negotiated between manufacturer and purchaser. Approved April 15, asmt For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown. Samples for analysis should be stored in suitable containers.
Titanium Plates, Sheets & Coils
This specification covers annealed titanium and titanium alloy strip, sheet, and plate. Individual reprints single or multiple copies of this standard may be asgm by contacting ASTM at the above address or at phonefaxor service astm. Other elements may not be added intentionally. The grades of titanium and titanium alloy metal covered by this specification shall have the chemical composition requirements of: C Single values are maximum.
Alternate Yield Strength Maximum S2. Unalloyed titanium plus 0.
Other industry standard methods may be used where the ASTM test methods in 2. Grades 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. Samples shall be taken from the ingot or the extremes of the product sstm be analyzed.